The bump and run is open to men and women who have a valid driver’s license. In the best interest and in fairness to all contestants the following rules and regulations shall prevail.
THIS IS NOT A SET OF RULES BUT A SET OF GUIDELINES OF HOW TO BUILD YOUR CAR. IF IT DOESN’T SAY YOU CAN SPECIFICALLY DO SOMETHING THEN YOU CANT. Driver Entry Driver must be at least 16 yrs. of age. Under 18 must have a parental release form signed by parent/legal guardian. Drivers may have one rider if so desired. Rider must also abide by all event regulations. If you registered as a driver you must remain the driver throughout the event. Only the driver will be eligible for any money awarded. All drivers must be register and have car teched ½ hour prior to the event start time, if not Lucky 7's Promotions LLC has the right to refuse anyone or charge an extra entry fee.
This is not a set of rules, but a set of guidelines of how to build your car. If it doesn’t say you can specifically do something, then you can’t. Please call if you have any questions on this!!! 573-375-0148 or 573-375-1717.
Participation regulations There will be a predetermined amount of laps per heat and features. A car must make a complete lap to be officially counted towards their total laps. Driver can go forwards or backwards, whatever it takes to get you around the track. No deliberate head-ons or hitting an opponent’s driver’s door. Driver/Passenger must remain in his/her car until car is removed from track or an official tells you directly. All drivers must attend drivers meeting prior to event start time. Protests should be directed to the main official at the earliest possible time. There will be a $100 cash in hand protest fee. The protester must be in the top eight in the main event to be able to protest. Alcohol or drug use will not be tolerated, if found to be under the influence of alcohol or drugs prior to the event being over, immediate disqualification will occur
Preparation of Cars
General: Open to any cars, vans, compact trucks or suv's not exceeding factory 112.9-inch wheelbase. No shortening wheelbase on car. Cars shall not have engines bigger than 6 cylinders. Put car number on both front doors and on a MANDATORY upright roof panel (15” X 15” min.) in large readable print. Must be able to read number to be scored correctly. Battery must be placed in a secured container within the cab and be securely covered with a non-conductive material such as a rubber floor mat. You will disqualified If battery becomes loose during event Car hood must have a hole in it large enough for a fire extinguisher to access the engine compartment. All cars must have a bar attached to center of windshield area to prevent hood from entering drivers’ compartment. Sunroof must be completely covered with metal. All glass, chrome, carpet, back seat, headliner and anything flammable must be removed. Fire extinguisher is recommended but not mandatory and must be securely mounted and must work. Stock safety belts or racing type safety belts must be used during the event. Stay securely fastened during your race even if your car is inoperable. DOT approved drivers helmet must be worn and properly fastened. Fire protective suit, neck brace and eye protection should be used. Cars must be able to stop at the tech line. Working brakes are required. Creasing of the cars is allowed. Hoods can be secured with 4 pieces of threaded rod, with mounting plates no larger than 4x4x1/4 plate. Up to 1” all-thread can be used.
Cage: Drivers and passengers doors may have at least one flat steel plate (1/2 inch minimum thickness and 6 inch minimum width) bolted to door. Length is at least 5 inches past driver and front passenger door seams but not exceeding past the center of each wheel on each side of vehicle. This plate must be bolted to door with at least three bolts 1/2 inch diameter or larger going throw door with a plate on the inside. Cars must have one pipe welded or bolted from drivers’ side to passenger side door pillars. A round butt plate may be welded to end of pipe to attach to door pillar. Cars Must have at least 2 door bars for drivers protection. These must overlap both vertical door seams. No grader blades on the inside without grader blades on the outside. Drivers and passenger’s door may be welded solid, all other doors must be welded, wired or chained shut. Anything within the driver area is allowed as long as it is for driver’s protection. A four point cage is extremely recommended.
Gas Tank: If the original stock gas tank is factory located completely in front of the rear axle it can remain and be used in this position. Stock gas tank must be removed if it is above or behind rear axle. Stock fuel tank not being used must be removed from car. NO PLASTIC AUXILIARY FUEL TANKS ALLOWED. If car was originally equipped with an electric fuel pump located in the fuel tank, this tank can be used in the backseat area of the car. All extra fuel lines must be plugged. Auxiliary tank must be secured to floorboard and covered with a secured rubber mat. If gas tank is leaking, you will not run.
Bumpers/Radiator Protectors: One or two horizontal pieces of round or square tubing may be placed in front of radiator, to be supported by two vertical pieces of tubing coming off frame with a support tube not exceeding 10” back from the end of the frame. All tubes not to exceed 2” in outside dimension. This is designed as a radiator protector, not a battering ram. If you run a tubing "bumper", then this will count as one of your radiator protectors and can only have one additional bar. Max 6x6 tubing. Radiators must remain in stock location.
Suspension/Steering: You may reinforce tie rods You may reinforce trailing arms you may reinforce axles You may reinforce A arms You may reinforce spindles you are allowed 1 bar that goes in between rear suspension that prevents tires from bending inward. NO DONUT TIRES ALLOWED ON DRIVE AXLE without official approval. Any wheel tire combo can be used. Stuffed or tubed tires are allowed. No studded tires No Screws in tires All wheel weights must be removed. Aftermarket motor mounts are allowed. You may reinforce stock motor mounts. Motor Cradles are allowed. Cannot be tied into frame or bumper in order to strengthen the car. These must be mounted where the stock mounts are located. These must only be secured to the motor and to the mounts. Skid plates are allowed. Cannot be welded solid to the frame. This needs to be to protect the motor, not strengthen the car. No added motor mounts. THE JUDGES DECISIONS ARE FINAL.
Entry Fee All competitors must pay general gate admission. All persons entering pits must sign waiver & pay pit entry fee. Entry fee is for driver only, Rider must pay additional entry fee. Pit passes are available for crew members